Tikkurila worldwide
UAB Tikkurila PRODUKTO TECHNINIŲ DUOMENŲ LAPAS
23.07.2009

Temacoat GPL-S Primer

Coatings
MED
APIBŪDINIMAS A two component, polyamide-cured high build epoxy primer containing zinc phosphate.
PRODUKTO SAVYBĖS Used as a primer or an intermediate coat in epoxy and polyurethane systems exposed to abrasion and/or chemical stress. Can be used as an intermediate coat on zinc-rich epoxy and zinc silicate paints.
Rekomenduojamos naudojimo sritys Recommended for bridges, haulage equipment, cranes, steel masts, conveyors and other steelwork, machinery and equipment.

TECHNINĖ INFORMACIJA
Savybės Excellent adhesion to steel, zinc and aluminium surfaces. Rapidly recoatable. The product has MED (Marine Equipment Directive) certificate no 0809-MED-0393 and is thus accepted for painting surfaces inside the ships.
Spalvų katalogai Temaspeed Primers colour card. TEMASPEED tinting.
Gloss groups Pusiau matinis
Išeiga

Recommended film thicknesses

Theoretical coverage

dry

wet

 

50 µm

90 µm

11.0 m2/l

100 µm

185 µm

5.5 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Skiediklis 1031
Maišymo santykis Base 4 parts by volume 179-series
Hardener 1 part by volume 008 5600 or 008 5605 (fast)
Dažymo metodas By airless spray or by brush.
Mišinio gyvybingumas ( 23°C) 6 hours with Hardener 008 5600
3 hours with Hardener 008 5605
Džiūvimo laikas

DFT 70 µm

0 ºC

+ 5 ºC

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

with Hardener 008 5600

4 h

2 h

1 h

½ h

15 min

with Hardener 008 5605

3 h

1½ h

¾ h

½ h

12 min

Touch dry, after

with Hardener 008 5600

22 h

11 h

5 h

2½ h

2 h

with Hardener 008 5605

12 h

6 h

3 h

2 h

1 ½ h

Recoatable with epoxy paints, min. after

with Hardener 008 5600

30 h

20 h

6 h

2 h

1 h

with Hardener 008 5605

18 h

12 h

4 h

1½ h

¾ h

Recoatable with polyurethane paints, min. after

with Hardener 008 5600

2 d

32 h

18 h

6 h

3 h

with Hardener 008 5605

1 ½ d

18 h

12 h

4 h

2 h

Recoatable without roughening max. 6 months

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Nelakių medžiagų kiekis pagal tūrį 55 ± 2 % voulme % (ISO 3233)
68 ± 2 % weight %.
Tankis 1.3 - 1.4 kg / l (mixed)
Produkto kodas 179-series
MED sertifikatas VTT-C-4031-15-09 Temacoat GPL-S primer

NAUDOJIMO INSTRUKCIJA
Dažymo sąlygos All surfaces must be clean and dry and free from contamination. The temperature of the substrate should be minimum 0 °C and at least 3 ° C above the dew point of the air. The product should not be applied at temperatures below 0 °C where there is a possibility of ice formation on the substrate. The temperature of paint itself should be above + 15 °C for proper application.
Good ventilation is required in confined areas during application and drying.

Note! There is a natural tendency of epoxy coatings to chalk and discolor on exterior exposure
Paviršiaus paruošimas Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with PANSSARIPESU detergent.

Hot dip galvanized surfaces are recommended to be painted with a mist coat (paint thinned 25 - 30 %) before the actual priming.

Aluminium surfaces: Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN AL detergent.

Stainless steel: Roughen the surface by grinding or sweep blasting using non-metallic abrasives.

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Priming TEMACOAT GPL-S PRIMER, TEMABOND, TEMAZINC 77, TEMAZINC 88, TEMAZINC 99 and TEMASIL 90.
Baigiamasis sluoksnis TEMACOAT GPL, TEMACOAT GS 50, TEMACOAT RM 40, TEMACOAT SPA 50, TEMADUR, TEMATHANE, TEMACRYL EA, FONTECOAT EP 50, FONTECOAT EP 80, and FONTEDUR 90.
Dažymas By airless spray or by brush. At airless spray application the paint should be thinned
0 - 10 % by volume. Airless spray nozzle tip 0.011" - 0.017" and nozzle pressure 120 - 160 bar. Spray angle shall be chosen according to the shape of the object. At brush application the paint should be thinned according to the circumstancies.
Komponentų maišymas First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squarrel Mixer for mixing.
Įrankių plovimas Thinner 1031.
EU VOC 2004/42/EB ribinė vertė The Volatile Organic Compounds amount is 430 g/litre of paint mixture.
VOC content of the paint mixture (thinned 30 % by volume) is 540 g/l.

SVEIKATOS IR SAUGOS ŽENKLINIMAS
Pagal reglamentą EB Nr. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.
Safety data sheetTEMACOAT GPL-S PRIMER [GB-ENG]
Thinner safety data sheetTHINNER 1031 [GB-ENG]
Hardener safety data sheetHARDENER 008 5600 [GB-ENG]
 
-


Atgal