TECHNINIŲ DUOMENŲ LAPAS
22.02.2006

Fontecoat EP 80 - Water-borne epoxy topcoat

 
Fontecoat_EP80
APIBŪDINIMAS A two component waterborne epoxy topcoat.
SAVYBĖS Used as a topcoat in epoxy paint systems for steel surface. Can also e applied onto concrete substrate e.g. walls, plasterboard etc.
Paskirtis -

TECHNINIAI DUOMENYS
Papildomos savybės Resistant against modest mechanical and chemical stress.
Spalvų katalogai TEMASPEED FONTE tinting.
Blizgumas Blizgus
Teorinė išeiga

Recommended film thicknesses

Theoretical coverage

dry

wet

 

50 µm

105 µm

9.4 m2/l

80 µm

170 µm

5.9 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Skiediklis Vanduo
Maišymo santykis Base 1 part by volume 169-series
Hardener 1 part by volume 007 1019
Įrankiai By airless spray or brush.
Mišinio tinkamumo trukmė (esant +23 ºC temperatūrai) 1½ h.
Džiūvimo laikas

DFT 70 µm

+ 15 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

4 h

2 h

1 h

Touch dry, after

8 h

5 h

2 h

Recoatable by itself, after

16 h

6 h

4 h

Fully cured, after

14 d

7 d

3 d


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Sausasis likutis 47 ± 2 volume % (ISO 3233)
61 ± 2 weight %
Tankis 1,4 kg/l käyttövalmis seos.
Gaminio kodas 169-series

NAUDOJIMO INSTRUKCIJA
Dengimo sąlygos All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +15 ºC during application and drying. Relative humidity should not exceed 70 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.
Paviršiaus paruošimas Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Priming FONTECOAT EP PRIMER and TEMACOAT GPL-S PRIMER.
Viršutinio sluoksnio danga FONTECOAT EP 80.
Dažymas By airless spray or brush. If necessary, the paint can be thinned 0 - 10 %. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 140 - 180 bar. Spray angle shall be chosen according to the shape of the object.
Komponentų maišymas First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.
Įrankių valymas Water or a mixture of water and Thinner 1029, 1:1. The equipment must be cleaned immediately after use before the paint dries.
Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB) Haihtuvien orgaanisten yhdisteiden määrä on 70 g/litra maalia.
Maaliseoksen VOC (ohennettu 10 tilavuus-%) 65 g/l.

SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS
pagal reglamentą EB Nr. 1272/2008
Noudatettava varoitusetiketin ohjeita. Tuotteen käyttöturvallisuustiedotteessa on selostettu tarkemmin käyttöön liittyvät vaarat ja tarpeelliset suojaustoimenpiteet. Käyttöturvallisuustiedote on saatavilla TIKKURILA COATINGS OY:ltä.
Saugos duomenų lapasFontecoat EP 80
Kietiklio saugos duomenų lapasFontecoat EP 80
 
-


Atgal