TECHNINIŲ DUOMENŲ LAPAS
13.01.2014

Temafloor AC602 Clear - Solvent-free acrylic topcoat

 
Temafloor AC602 Clear
APIBŪDINIMAS A two-component, solvent-free acrylic topcoat.
SAVYBĖS Recommended for the floors of engineering workshops, warehouses, cold stores of food industry, parking deck surfaces, loading ramps and terraces.
Paskirtis Used as a topcoat for Temafloor AC502 acrylic troweling screed.

TECHNINIAI DUOMENYS
Papildomos savybės Forms elastic and durable surface.
Non-yellowing
Cures at low temperatures.
Blizgumas Pusiau matinis
Teorinė išeiga

Coverage is on the average:

 

Topcoat: 1.3–2.5 m2/l

 

Practical coverage depends on the porosity and evenness of the surface and on the application method.
Pakuočių dydžiai 200 l drum, content 190 kg.
Įrankiai Topcoat Temafloor AC602 Clear lacquer mixture is applied with a rubber trowel and level with a roller.
Ypatinga savybė Mixing table

Temperature (oC)*

The amount of hardener (percentage of weight of the binder)

Pot life (min)

Drying time (min)

+5

4.5

ab. 40

ab. 70

+10

3.0

ab. 35

ab. 75

+20

2.0

ab. 15

ab. 35

+35

1.0

ab. 25

ab. 70


* Temperature of the binder, air and the floor.

Possible hardeners: BP-50-FT, Perkadox®CH-50 or PEROXAN BP-Pulver 50 W.
Sausasis likutis approx. 100 vol-%.
Tankis 0.95 kg /l (ready made mixture)
Gaminio kodas 001 6091

NAUDOJIMO INSTRUKCIJA
Dengimo sąlygos The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +5ºC during either application or drying. Relative humidity of air should not exceed 80%.
Paviršiaus paruošimas New concrete
Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

Old concrete
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding, milling or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.
Skiedimas Do not thin.
Lakavimas Topcoating can be carried out after the coating or screed has cured. Pour the varnish mixture onto the floor, spread with a rubber trowel and level with a roller.
Observe a right amount of hardener. Using excessive amounts of hardener can cause yellowing and may weaken the properties of the topcoat. The film thickness of the Temafloor AC602 should be 0,4–0,8 mm. Too thick film thickness may also cause yellowing of the surface.
Komponentų maišymas Mix the correct proportions of base and hardener powder thoroughly (approx. 2 minutes) by using a hand drill with a paddle, concrete mixer or power mixer. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficiejnt mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the varnish and risk the success of the application.
Įrankių valymas Cleaning of equipment with Thinner 006 1400.
Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB) VOC 2004/42/EC (cat A/j), 500 g/l (2010)
Temafloor AC602 Clear: max. VOC < 500 g/l

SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS
pagal reglamentą EB Nr. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For professional use only.
Saugos duomenų lapasTEMAFLOOR AC602 CLEAR [GB-ENG]
 
-


CE
CE logo
Lämpöyhteensopivuus



Atgal