TECHNINIŲ DUOMENŲ LAPAS
Temafloor AC610 Clear - Solvent-free acrylic top lacquer
|APIBŪDINIMAS||A two-component, solvent-free acrylic top lacquer.|
Suitable for topcoating of Temafloor AC509 and Temafloor AC501 acrylic screeds. Especially for hard mechanical abrasion in dry interior premises.
|Paskirtis||Suitable for dry indoor premises, such as corridors, retail stores, changing rooms etc.|
|Papildomos savybės||Excellent resistance to abrasion and scratches.
Good resistance to chemicals.
|Spalva||Sunlight will affect on the shade and the gloss of the varnish in the long run.|
* Temperature of the binder, air and the floor.
is on the average:
Topcoat 1.5–3.3 m2/l
|Pakuočių dydžiai||200 l drum, content 190 kg|
|Įrankiai||Apply with a rubber spatula and level with roller.
|Sausasis likutis||approx. 100 vol-%.|
|Tankis||0.99 kg /l (ready made mixture)|
|Gaminio kodas||001 6093|
|Dengimo sąlygos||The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +5ºC during either application or drying. Relative humidity of air should not exceed 80%.|
|Paviršiaus paruošimas||New concrete
Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding, milling or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.
|Skiedimas||Do not thin.|
|Lakavimas||Topcoating can be carried out after the coating or screed has cured. Pour the mixture onto the floor, spread with a rubber trowel and level with a roller.
Observe a right amount of hardener. Using excessive amounts of hardener can cause yellowing and weaken the properties of the topcoat. Film thickness of Temafloor AC610 Clear should be 0.3–0.7 mm. Larger or too thick film thickness may also cause yellowing and delamination of the topcoat.
|Komponentų maišymas||Mix the correct proportions of base and hardener powder thoroughly (approx. 2 minutes) by using a hand drill with a paddle, concrete mixer or power mixer. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the varnish and risk the success of the application.|
|Įrankių valymas||Cleaning of equipment with Thinner 006 1400 or Temafloor AC Clean.|
|Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB)||VOC 2004/42/EC (cat A/j), 500 g/l (2010)
Temafloor AC609 Clear: max. VOC < 500 g/l
|SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS|
pagal reglamentą EB Nr. 1272/2008
|Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For professional use only.|
|Saugos duomenų lapas||TEMAFLOOR AC610 CLEAR en|
|The European harmonized productstandard EN 1504-2:2004 defines the requirements for surface protection systems for concrete.
This product is tested and CE-labelled in accordance with the tables 1d, 1f and 1g in the appendix ZA.
|1) Tested as part of a system together with Temafloor AC 102 Primer and Temafloor AC 509.|