TECHNINIŲ DUOMENŲ LAPAS
10.01.2007

Temafloor PU-UV - Polyurethane coating

 
Temafloor_PU-UV
APIBŪDINIMAS A high solids, two-component polyurethane coating.
SAVYBĖS Intended as a UV-resistant topcoat on TEMAFLOOR PU-floors in parking decks and other areas exposed to direct sunlight.
Paskirtis Concreet floors.

TECHNINIAI DUOMENYS
Papildomos savybės Withstands medium mechanical and chemical stress. Good impact resistance. Self-levelling, to be applied with serrated or steel trowel.
Spalva TVT 0229. The shade and gloss of the coating may change during time.
Blizgumas Blizgus
Teorinė išeiga

Practical coverage depends on the porosity and evenness of the substrate and on the application method.

Film thickness 0.3 mm coverage approx. 2.7 m2/litre

Film thickness 0.5 mm coverage approx. 1.8 m2/litre
Maišymo santykis Base 2 parts by volume 008 4000
Hardener 1 part by volume 008 4001
Įrankiai Serrated or steel trowel.
Mišinio tinkamumo trukmė (esant +23 ºC temperatūrai) 40 minutes on substrate, abt. 20 minutes in the mixing container.
Džiūvimo trukmė (esant +23 °C temperatūrai ir 50 proc. santykiniam oro drėgniui)

Dust dry after 6 hours

Light trucking after 24 hours

Fully cured after 7 days

 

At lower temperatures the curing process will last longer.
Sausasis likutis Approx. 90 % volume
Tankis 1.4 kg / litre (mixture)
Gaminio kodas 008 4000

NAUDOJIMO INSTRUKCIJA
Dengimo sąlygos The relative humidity of the concrete should not exceed 97 %. The temperature of the ambient air, surface or coating should not fall below + 15 ºC during application or drying. Relative humidity of air should not exceed 70 %.
Paviršiaus paruošimas Remove dust and loose particles from the floor. Remove all grease, oil and other impurities by detergent washing.
Skiedimas Do not thin TEMAFLOOR PU-UV polyurethane coating.
Dengimas Overcoating may be carried out not earlier than 24 hrs after coating with TEMAFLOOR PU. If the coated surface is older than 7 days, it should be abraded. Pour the coating mixture onto the floor and spread it with a serrated steel trowel or an adjustable trowel. Control that the thickness of layer is correct by observing coating consumption and by measuring the film thickness. Recommended thickness of a layer is 0.3 mm. Level the screed with a spiked roller approx. 10 - 20 min after application. Spiked roller helps removing air bubbles from the coating.

Note! Add the remaining mixture to the next batch of the screed, do not scrape it out of the container onto the floor.
Komponentų maišymas Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a low speed hand drill with a paddle. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Įrankių valymas Thinner 1061.
Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB) VOC 2004/42/EC (cat A/j) 550 g/l (2007), 500 g/l (2010)
Temafloor PU-UV: max. VOC < 500 g/l

SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS
pagal reglamentą EB Nr. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.
Saugos duomenų lapasTemafloor PU-UV
Kietiklio saugos duomenų lapasTemafloor PU-UV
 
-


Atgal