TECHNINIŲ DUOMENŲ LAPAS
27.08.2015

Akvi Isolator - Isolating primer

 
Akvi Isolator
APIBŪDINIMAS A water-borne acrylate primer.
SAVYBĖS Wooden interior surfaces.
Paskirtis Recommended for interior wooden panels, mouldings, doors, etc.

TECHNINIAI DUOMENYS
Papildomos savybės • A fast-drying water-borne primer with isolating properties.
• Retards knot bleeding.
• Slows down discolouring of topcoat caused by resins. In order to reach good isolating properties it is recommended to apply two layers.
Spalva White.
Blizgumas Matinis
Teorinė išeiga

Recommended spreading amounts (unthinned)

Theoretical coverage

dry

wet

 

43 µm

150 g/m2

8–9 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Skiediklis Vanduo
Džiūvimo laikas

150 g/m2  wet paint

+23ºC

+50ºC

Dust dry, after

35 min

5–10 min

Dry to sand, after

 60 min

5–10 min


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Sausasis likutis 38 % by volume and 51% by weight.
Tankis 1.3 kg/litre.
Gaminio kodas 005 3841

NAUDOJIMO INSTRUKCIJA
Dengimo sąlygos The surface to be treated has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the primer has to be over +18ºC and the relative humidity of the air below 70%.
Paviršiaus paruošimas Wood surfaces should be sanded with sandpaper P150–320. Primed surfaces should be sanded with sandpaper P320–600. All sanding dust must be removed.
Dažymas For airless spraying, the product can be thinned approximately 0–5% by water if needed. Recommended nozzle tip is 0.011"–0.013" and pressure 80–160 bar. Spray angle shall be chosen according to the shape of the object.

For air–assisted airless spraying, the product can be thinned approximately 0–5% if needed. Recommended nozzle tip is 0,011"–0,013" and pressure 40–140 bar. Atomising air pressure should be about 1–3 bar. Spray angle shall be chosen according to the shape of the object.

For conventional spraying the product is thinned approximately 0–5% to the viscosity 60–80s (DIN4). Recommended nozzle tip is 1.4–1.8 mm and pressure 2–3 bar.

Apply 1–2 times.
Viršutinio sluoksnio danga Akvi Top DS 25, Akvi Top FD 30 and Luminol 25.
Komponentų maišymas Stir the paint carefully before use. Avoid flotation. If necessary thin the paint with water.
Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB) The Volatile Organic Compounds amount is 37 g/litre of paint.
Maximum VOC content in ready to use paint is 37 g/l.

SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS
pagal reglamentą EB Nr. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial and professional use only.
Saugos duomenų lapasAKVI ISOLATOR
 
-


Atgal