Temalac ML 90 - Alkyd topcoat

APIBŪDINIMAS A high gloss, one component alkyd topcoat.
SAVYBĖS High gloss alkyd topcoat for steel surfaces. Can be applied using a "wet-on-wet" painting technique. Suitable for industrial finishing.
Paskirtis Recommended uses: small tanks, agricultural machinery, haulage equipment and other machinery and equipment.

Papildomos savybės Good gloss and colour retention when exposed to weathering.
Spalvų katalogai RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting.
Blizgumas Labai blizgus
Teorinė išeiga

Recommended film thicknesses

Theoretical coverage




40 µm

90 µm

11.2 m2/l

60 µm

135 µm

7.5 m2/l

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Skiediklis 1006 ir 1054
Įrankiai By airless or conventional spray or by brush.
Džiūvimo laikas

DFT 40 µm

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

2 h

1 h

½ h

Touch dry, after

8 h

5 h

3 h

Recoatable, after

36 h

24 h

16 h

Recoatable, "wet-on-wet", after


½ - 1 h


Touch dry 1 h / 60 ºC, ½ h / 80 ºC




Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Sausasis likutis 45 ± 2 volume % (ISO 3233)
57 ± 2 weight %
Tankis 0.9 - 1.1 kg / l depending on colour.
Gaminio kodas 513-series

Dengimo sąlygos All surfaces must be dry. The temperature of the ambient air, surface and paint should not fall below + 5ºC during application and drying. Relative humidity should not exceed 80%. The temperature of the substrate should remain at least 3ºC above the dew point.
Paviršiaus paruošimas Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Priming Temaprime EE, Temaprime EUR, Temaprime GF, Temaprime ML and Fontecryl 10.
Viršutinio sluoksnio danga Temalac ML 90.
Dažymas By airless spray or by brush. Mix the paint thoroughly before use. At airless spray the paint should be thinned 0 - 10%. Airless spray nozzle tip 0.011" - 0.015" and nozzle pressure 140 - 180 bar. Spray angle shall be chosen according to the shape of the object. The best finish is obtained using a "wet-on-wet" technique, with 5 - 30 minutes evaporating pauses.
Įrankių valymas Thinner 1006 or Thinner 1054.
Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB) The Volatile Organic Compounds amount is 460 g/litre of paint.
VOC content of the paint (thinned 10 % by volume) is 500 g/l.
Only for industrial and professional use.

pagal reglamentą EB Nr. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.