TECHNINIŲ DUOMENŲ LAPAS
02.01.2006

Temanyl MS Primer - Vinyl primer

 
Temanyl_MS_Primer
APIBŪDINIMAS A one component modified vinyl primer.
SAVYBĖS Suitable for underwater steel, zinc and aluminium structures like ship bottoms etc. Used also as a primer under conventional and selfpolishing antifoulings. Can also be applied at low temperature conditions. Suitable to be used as a primer under vinyl, chlorinated rubber and acrylic topcoats.
Paskirtis Steel surfaces.

TECHNINIAI DUOMENYS
Papildomos savybės Good abrasion, immersion and atmospheric resistance.
Spalva Aluminium (reddish aluminium with Temaspeed tinting).
Blizgumas Matinis
Teorinė išeiga

Recommended film thicknesses

Theoretical coverage

dry

wet

 

60 µm

160 µm

6.3 m2/l

100 µm

265 µm

3.8 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Skiediklis 1006
Įrankiai By spray or brush.
Džiūvimo laikas

DFT 80 µm

+ 5 ºC

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

2 h

1½ h

1 h

½ h

Recoatable, after

6 h

4 h

3 h

2 h


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Sausasis likutis 38 ± 2 % volume (ISO 3233)
53 ± 2 % weight
Tankis 1.1 kg / l
Gaminio kodas 008 6740

NAUDOJIMO INSTRUKCIJA
Dengimo sąlygos The surface has to be dry. The temperature of the ambient air, surface or paint should not fall below - 5 ºC during application and drying. During application and drying the relative humidity should not exceed 80 %. The surface temperature should remain at least 3 ºC above the dew point.
Paviršiaus paruošimas Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN ZN detergent.

Aluminium surfaces: Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with FONTECLEAN AL detergent.

Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Instaliacija TEMANYL MS PRIMER, TEMABOND, TEMAZINC 77, TEMAZINC 88 and TEMAZINC 99.
Instaliacija TEMACRYL AR 50 and TEMACHLOR 40.
Instaliacija By spray or brush. Mix the paint thoroughly before use. Depending on the application method the paint can be thinned 0 - 5 %. Airless spray nozzle tip 0.018" - 0.023", spray angle 65º - 80º and nozzle pressure 15 MPa (150 bar).
Komponentų maišymas Thinner 1006.
Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB) The Volatile Organic Compounds amount is 540 g/litre of paint.
VOC content of the paint (thinned 5 % by volume) is 557 g/l.

SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS
pagal reglamentą EB Nr. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oy.
Saugos duomenų lapasTemanyl MS Primer
 
-


Atgal