Automobilių stovėjimo aikštelių ir lėktuvų angarai

TECHNINIŲ DUOMENŲ LAPAS
13.01.2014

Temafloor AC601 Clear - Ssolvent-free acrylic topcoat

APIBŪDINIMAS

A two-component, solvent-free acrylic topcoat.

SAVYBĖS

Recommended for the floors of commercial buildings, warehouses, laboratories, and food processing industries.

Paskirtis

Used as a topcoat for Temafloor AC501 and Temafloor AC509 acrylic troweling screeds.

TECHNINIAI DUOMENYS

Papildomos savybės

Builds up hard and durable surface.
Non-yellowing.
Rapid curing also in low temperatures.

Spalva

Sunlight will affect on the shade and the gloss of the varnish in the long run.

Blizgumas

Pusiau matinis

Teorinė išeiga

Coverage is on the average:

Topcoat: 1.2–3.3 m²/l

Practical coverage depends on the porosity and evenness of the surface and on the application method.

Pakuočių dydžiai

200 l drum, content 180 kg

Įrankiai

Topcoat Temafloor AC601 Clear lacquer mixture is applied with a rubber trowel and level with a roller.

Adhezija

Mixing table

Tempe-rature (^oC)*	The amount of hardener (percentage of weight of the binder)	Pot life (min)	Drying time (min)
+5	2.0	ab. 13	ab. 35
+10	1.8	ab. 14	ab. 30
+15	1.5	ab. 13	ab. 30
+20	1.0	ab. 12	ab. 30
+25	0.8	ab. 12	ab. 30

* Temperature of the binder, air and the floor.

Possible hardeners: BP-50-FT, Perkadox®CH-50 or PEROXAN BP-Pulver 50 W.

Sausasis likutis

approx. 100 vol-%.

Tankis

001 6090

Gaminio kodas

001 6090

NAUDOJIMO INSTRUKCIJA

Dengimo sąlygos

The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +5ºC during either application or drying. Relative humidity of air should not exceed 80 %.

Paviršiaus paruošimas

New concrete
Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

Old concrete
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding, milling or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.

Skiedimas

Do not thin.

Lakavimas

Topcoating can be carried out after the coating or screed has cured. Pour the varnish mixture onto the floor, spread with a rubber trowel and level with a roller.
Observe a right amount of hardener. Using excessive amounts of hardener can cause yellowing and may weaken the properties of the topcoat. The film thickness of the Temafloor AC601 Clear should be 0,3-0,8 mm. Larger filmthickness may also cause yellowing of the surface.

Komponentų maišymas

Mix the correct proportions of base and hardener powder thoroughly (approx. 2 minutes) by using a hand drill with a paddle, concrete mixer or power mixer. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficiejnt mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the screed and risk the success of the application.

Įrankių valymas

Cleaning of equipment with Thinner 006 1400.

Lakiųjų organinių junginių kiekis (LOJ) (direktyva 2004/42/EB)

VOC 2004/42/EC (cat A/j), 500 g/l (2010)
Temafloor AC601 Clear: max. VOC < 500 g/l

SAUGOS IR SVEIKATOS APSAUGOS ŽENKLINIMAS
pagal reglamentą EB Nr. 1272/2008

Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For professional use only.

Saugos duomenų lapas

TEMAFLOOR AC601 CLEAR en


Adhesion after thermal compatibility

Aukščiau pateikta informacija yra pagrįsta laboratoriniais bandymais ir praktine patirtimi, patvirtinta nuo datos, nurodytos produkto duomenų lape. Produkto kokybę užtikrina mūsų veiklos sistema, pagrįsta ISO 9001 ir 14001 reikalavimais. Gamintojas neatsako už žalą, patirtą naudojant produktą ne pagal instrukciją ar netinkamu tikslu.

Atgal